CRM Mitchell1, Author at R A E an Automotive Service Co Inc

2013 RAM 2500 HD
Mileage
82,295
Service Date
10/26/2022
Services Performed
Pulse/Shimmy:Yes_____NO___X__Front_____Rear_____ Brake Pull: YES____X_____NO______ Brake Pads/Shoes: (MM) RF 10mm LF 10mm RR 6mm LR 6mm Emergency Brake Shoes LR 4mm RR 4mm Disc/Drum Front – Spec: 37.4mm Rear – Spec 32.4mm RF 39.21mm LF 39.19mm RR 34.12mm LR 34.02mm After Machining: N/A RF________LF________RR________LR_________ Surface________________________________ Wheel Bearings: OK_____X_____Not ok_______ Hydrualics – Master Cyl: Ok__X___Not ok______ Front Calipers: OK_________Not OK__X___ Rear Calipers / Wheel Cyls: OK____X_____Not ok______ Brake Lines: OK___X____Not ok________ Wheel Torque 140Ftlbs Tire Pressure – F= 60psi R= 80psi Brake Fluid Condition: OK__X___Not OK____ ppm =_______ Front Suspension: OK__X___Not OK______ Rotor runout, if necessary: N/A Rotor Parrelism, if necessary: N/A NOTES: Caliper replaced and is no longer hanging up. Did notice slight uneven tire wear due to ball joints starting to fail. Will also need upper steering column intermediate shaft to be replaced due to steering wheel play. Will also need another alignment after these repairs. Currently, the vehicle is driving straight, steering wheel was straightened but still has some play.
Air filter – OK Cabin filter – OK Belts – OK Hoses – OK Engine oil – OK Engine coolant – OK Tire Pressure – F 60 R 80 Tires – RF 10/32 LF 10/32 RR 10/32 LR 10/32 Tire Date codes – 2021 Visual Brake inspection – F 10mm R 6mm
CALIPER – Remove & Replace – Front, One Side – [Includes: Bleed Brake System and replace Pads (if necessary).]
* Remove old brake fluid from the master cylinder * Clean reservoir of any debris as best as possible * Install new brake fluid * Bleed each wheel according to the factory specified sequence * Top off fluid to the proper level * Clean each bleeder screw area of fluid * Reinspect for leaks * Inspect brake pedal for the proper travel * Test drive the vehicle
Alignment- Reset Steering / Traction Controls Using The Code Link ALDL Interface Connector. Front Suspension: BAD (NEED TO REPLACE UPPER AND LOWER BALL JOINTS ON BOTH SIDES) Front Brakes – visual: GOOD Rear Suspension: GOOD Rear Brakes – visual: GOOD Tire pressures: F 60 R 80 Tire wear= EVEN Tires – Tread depth – LF 10/32 RF 10/32 LR 10/32 RR 10/32 Steering Wheel= STRAIGHT Drives before – OFF TO THE RIGHT After – GOOD Notes: Set toe, when applicable, Caster & Camber adjustments if needed, are a extra charge ***See attached print out***
Dan C. gave our service a 5 star review on 10/28/2022
2015 Lincoln MKC
Mileage
111,527
Service Date
10/25/2022
Services Performed
Complete hookup & analysis on Scope or Scanner 1. Confirm problem : Yes 2. Monitors : Incomplete 3. Computer codes : PO420- CATALYST SYSTEM EFFICIENCY BELOW THRESHOLD BANK 1 4. Mode 6 data: OK 5. Visual test : N/A 6. Engine vac. @ idle : N/A 7. Engine vac. @ 2500 : N/A 8. Smoke test : N/A 9. Diagnostics : Checked catalyst converter temp with thermal temp gun. Inlet temp is higher than outlet temp. Also upstream O2 sensor #1 is mirroring O2 sensor #2. Downstream O2 mirrored sensor #1 when propane was added to intake stream. Also checked fuel pressure. Tested back pressure at O2 sensor #1, has about 2 PSI at idle and about 8 PSI at wide open throttle. Recommend to replace Catalytic Converter Bank 1. After repairs cleared codes and test drove vehicle. No stalling and no codes returned. Mode 6 passed. All drive cycle monitors cleared / passed at this time. 10. Confirm fix: YES Tire Pressure F= 35 R= 35 Complementary inspection Air filter – OK Cabin filter – OK Belts – OK Hoses – OK Engine oil – OK Engine coolant – OK Tires – RF_9/32____LF_9/32_____RR_6/32_____LR_6/32_____ Tire Date codes – 2021/2018 Visual Brake inspection – F__7mm________R_8mm________
CATALYTIC CONVERTER – Remove & Replace
Car Wash – Complementary – THANK YOU ::))
Michael C. gave our service a 5 star review on 10/25/2022
2013 Subaru Impreza
Mileage
166,724
Service Date
10/7/2022
Services Performed
Complete hookup & analysis on Scope or Scanner 1. Confirm problem : Yes 2. Monitors : Complete 3. Computer codes : P0302 & P0303 4. Mode 6 data: Pass/Fail – Info – N/A 5. Visual test : FOUND OIL ON CYLINDER #2&4 WHEN REMOVING PLUGS TON INSPECT. 6. Engine vac. @ idle : N/A 7. Engine vac. @ 2500 : N/A 8. Smoke test : N/A 9. Diagnostics : SCANNED FOR CODES AND FOUND P302 & P0303. BEGAN BY TESTING RESISTANCE ON FUEL INJECTORS. INJECTORS TESTED WITHIN SPECS OF 12-13 OHMS. NEXT REMOVED SPARK PLUGS TO EVALUATE. PLUGS APPEARED TO BE FOULED AND HAD CARBON BUILD UP. WHILE REMOVING SPARK PLUGS NOTICED OIL ON CYLINDER #2 & 4. RECOMMEND TO REPLACE SPARK PLUGS WITH ALL IGNITION COILS. RECOMMEND TO REPLACE BOTH VALVE COVER GASKETS. FLUID LEAKING IS TRANSMISSION FLUID. TRANSMISSION IS CRACKED AT FILL PLUG. RECOMMEND TO REPLACE TRANSMISSION DUE TO CRACK ON CASING. REMOVED AND REPLACED SPARK PLUGS, IGNITION COILS AND VALVE COVER GASKETS. TRANSMISSION WILL BE REPLACED AT A DIFFERENT SHOP. AFTER REPAIRS TEST DROVE VEHICLE. NO FAULT CODES FOUND. NO LEAKS AT ANY CYLINDER. TRANSMISSION IS STILL LEAKING FLUID. WINDSHIELD WASHER FLUID LOW WARNING MESSAGE IS STILL ON. RECOMMEND TO REPLACE WASHER FLUID RESERVOIR WITH SENSOR. 10. Confirm fix: YES Tire Pressure F= 35 R= 35
SPARK PLUGS – Remove & Replace
VALVE COVER GASKET – Remove & Replace
Changed oil and oil filter. Lube Chassis & Driveline Check sheet: Transmission fluid: LEAKING Radiator water: ok Windshield wiper fluid: LOW WARNING LAMP IS ON Wiper Blades ok Battery water: ok Battery Date code:_2020____ Brake fluid ok Hyd. clutch fluid: N/A PS fluid: ok Air filter: ok Cabin Filter: OK Belts: ok Hoses: ok Shocks & suspension: ok Chassis lubrication: ok Oil leaks: TRANSMISSION LEAKING Lights: ok Tires: NOT OK Date codes: 2019 Tread depth – LF_3/32___RF_3/32_LR_6/32___RR_6/32__ Visual Brake inspection F=_7MM____ R=__4MM___ Oil Sticker: DOOR RESET OIL LIFE MONITOR:__YES_
Brianna B. gave our service a 5 star review on 10/7/2022
2008 Dodge Caliber
Mileage
166,427
Service Date
10/4/2022
Services Performed
Complete hookup & analysis on Scope or Scanner 1. Confirm problem : Yes 2. Monitors : Complete 3. Computer codes : P2004, P2118, P2110 4. Mode 6 data: Pass/Fail – Info – N/A 5. Visual test : N/A 6. Engine vac. @ idle : N/A 7. Engine vac. @ 2500 : N/A 8. Smoke test : N/A 9. Diagnostics : SCANNED FOR CODES AND FOUND P2004- INTAKE MANIFOLD RUNNER CONTROL STUCK OPEN, P118- ELECTRONIC THROTTLE CONTROL MOTOR CURRENT PERFORMANCE BANK 1 AND P2110- ELECTRONIC THROTTLE CONTROL SYSTEM BANK 1 FORCED LIMITED RPM. VEHICLE APPEARS TO A FAULTY THROTTLE BODY OR DIRTY THROTTLE BODY WILL NEED TO REMOVE TO INSPECT FURTHER. CUSTOMER REQUESTED TO REMOVE THROTTLE BODY AND REPLACE IT WITH NEW. WHILE THROTTLE BODY WAS REMOVED ALSO REMOVED INTAKE RUNNER VALVE TO MANUALLY TEST RUNNERS ON INTAKE MANIFOLD AND RUNNERS ARE STUCK, WONT TURN BY HAND. RECOMMEND TO REPLACE INTAKE MANIFOLD AND RE CHECKING. REMOVED & REPLACED THROTTLE BODY ASSEMBLY. CHECK ENGINE LIGHT WILL RETURN CURRENTLY IS OFF DUE TO US CLEARING CODES AFTER REPAIRS. 10. Confirm fix: YES Tire Pressure F= 35 R= 35 Complementary inspection Air filter – K&N Cabin filter – N/A Belts – OK Hoses – OK Engine oil – OK Engine coolant – OK Tires – RF_0/32____LF_0/32_____RR_5/32_____LR_5/32_____ Tire Date codes – 2018 Visual Brake inspection – F__6MM________R_7MM________
THROTTLE BODY ASSEMBLY – Remove & Replace
Tomas G. gave our service a 5 star review on 10/4/2022
2008 Dodge Caliber
Mileage
166,427
Service Date
10/4/2022
Services Performed
Complete hookup & analysis on Scope or Scanner 1. Confirm problem : Yes 2. Monitors : Complete 3. Computer codes : P2004, P2118, P2110 4. Mode 6 data: Pass/Fail – Info – N/A 5. Visual test : N/A 6. Engine vac. @ idle : N/A 7. Engine vac. @ 2500 : N/A 8. Smoke test : N/A 9. Diagnostics : SCANNED FOR CODES AND FOUND P2004- INTAKE MANIFOLD RUNNER CONTROL STUCK OPEN, P118- ELECTRONIC THROTTLE CONTROL MOTOR CURRENT PERFORMANCE BANK 1 AND P2110- ELECTRONIC THROTTLE CONTROL SYSTEM BANK 1 FORCED LIMITED RPM. VEHICLE APPEARS TO A FAULTY THROTTLE BODY OR DIRTY THROTTLE BODY WILL NEED TO REMOVE TO INSPECT FURTHER. CUSTOMER REQUESTED TO REMOVE THROTTLE BODY AND REPLACE IT WITH NEW. WHILE THROTTLE BODY WAS REMOVED ALSO REMOVED INTAKE RUNNER VALVE TO MANUALLY TEST RUNNERS ON INTAKE MANIFOLD AND RUNNERS ARE STUCK, WONT TURN BY HAND. RECOMMEND TO REPLACE INTAKE MANIFOLD AND RE CHECKING. REMOVED & REPLACED THROTTLE BODY ASSEMBLY. CHECK ENGINE LIGHT WILL RETURN CURRENTLY IS OFF DUE TO US CLEARING CODES AFTER REPAIRS. 10. Confirm fix: YES Tire Pressure F= 35 R= 35 Complementary inspection Air filter – K&N Cabin filter – N/A Belts – OK Hoses – OK Engine oil – OK Engine coolant – OK Tires – RF_0/32____LF_0/32_____RR_5/32_____LR_5/32_____ Tire Date codes – 2018 Visual Brake inspection – F__6MM________R_7MM________
THROTTLE BODY ASSEMBLY – Remove & Replace
Tomas G. gave our service a 5 star review on 10/4/2022
2020 Subaru Outback
Mileage
52,507
Service Date
9/23/2022
Services Performed
Changed oil and oil filter. Lube Chassis & Driveline Check sheet: Transmission fluid: SEALED Radiator water: ok Windshield wiper fluid: ok Wiper Blades ok Battery water: ok Battery Date code:_COVERED_ Brake fluid ok Hyd. clutch fluid: N/A PS fluid: N/A Air filter: ok Cabin Filter: OK Belts: ok Hoses: ok Shocks & suspension: ok Chassis lubrication: ok Oil leaks: ok Lights: ok Tires: ok Date codes: 2022 Tread depth – LF_8/32___RF_8/32__LR_8/32___RR_8/32__ Air Pressure F=_35____R=_33_____ Visual Brake inspection F=_8MM__ R=__3MM__ Oil Sticker: Door RESET OIL LIFE MONITOR:_N/A___
Re balance tires – Yes Rotate tires – Yes Wheels torqued – 90 FT LBS
Normand R. gave our service a 5 star review on 9/24/2022
2007 Dodge Pickup
Mileage
162,420
Service Date
9/13/2022
Services Performed
TRANSMISSION OIL FILTER – Remove & Replace – 4WD – Both
Check for rattle under vehicle, gfound LR shock bolt loose – Tighten LR shock bolt and torque,
Dave F. gave our service a 5 star review on 9/19/2022
2004 GMC Sierra
Mileage
62,012
Service Date
9/19/2022
Services Performed
Complementary inspection Air filter – OK Cabin filter – OK Belts – OK Hoses – OK Engine oil – OK Engine coolant – OK Tire Pressure – F 60 R 80 Tires – RF 9/32 LF 9/32 RR 9/32 LR 9/32 Tire Date codes – 2011 Visual Brake inspection – F 6mm R 6mm Notes: Vehicle had to be primed to start up. After re prime, a small leak was found coming from the fuel filter housing. Could hear filter sucking up air. Removed and replaced fuel filter housing, filter, and sensor. After repairs, tested for further fuel leaks or air in fuel, no leaks were found and no longer taking in air. Test drove vehicle, had no issues starting up, and vehicle did not ever shut off. Vehicle drives great and is holding prime.
FUEL FILTER HOUSING – Remove & Replace – Diesel Assembly (Complete) – [Includes: Bleed System.]
Alan B. gave our service a 5 star review on 9/19/2022
2021 Chrysler Pacifica
Mileage
18,743
Service Date
9/12/2022
Services Performed
Changed oil and oil filter. Lube Chassis & Driveline Check sheet: Transmission fluid: ok Radiator water: ok Windshield wiper fluid: ok Wiper Blades ok Battery water: ok Battery Date code – COVERED Brake fluid ok PS fluid: ok Air filter: ok Cabin Filter: OK Belts: ok Hoses: ok Shocks & suspension: ok Chassis lubrication: ok Oil leaks: ok Lights: ok Tires: ok Date codes: 2020 Tread depth – LF 6/32 RF 6/32 LR 6/32 RR 6/32 Air Pressure F= 36psi R= 36psi Visual Brake inspection F=6mm R= 6mm Oil Sticker: Door RESET OIL LIFE MONITOR – DONE
Sarah M. gave our service a 5 star review on 9/12/2022
2005 Nissan Murano
Mileage
174,341
Service Date
8/29/2022
Services Performed
Today's temp: 90 Degrees 0. Confirm Problem – Yes 1. Freon content in- R134 2. Recovered amount: 0 Spec- 1.2 lbs Needed- 1.2 lbs 3. Vacuum test: OK 4. After 10 minutes: 0 5. Check oil drain bottle after recovery: 0 6. Check compressor oil level: N/A 7. Oil Type: Pag_X___ 8. Recharged with: R-134A 1.2 LBS (18.56 OZ) 9. Pressure – Highside 200 Lowside 30 10. Vent outlet temp: 55 DEGREES IN SHOP AND 47 DEGREES DRIVING 11. Test for leaks with electronic leak detector: OK 12. Fan works: Yes__X___No_____ Weak fan clutch______ 13. Belts: OK__X____Not OK______ 14. Comments: LEAK AT COMPRESSOR HOSE CONNECTIONS. RECOMMEND HOSE CONNECTIONS O RINGS. RECOMMEND TO EVACUATE AND RECHARGE A/C SYSTEM AFTER REPAIRS. AFTER REPAIRS A/C WAS RE CHECKED AND FOUND NO LEAKS. AC BLOWS COLD. After Fill/Repair: Vacuum:__30____After 10 Minutes__29"______ Low Psi__30___High psi__200____A/C Temp___55 IN SHOP______ A/C Temp. @ vent now reading during test drive: 47 DEGREES WHILE DRIVING
Air filter – OK Cabin filter – OK Belts – OK Hoses – OK Engine oil – OK Engine coolant – OK Tire Pressure – 33 PSI FRONT AND REAR Tires – RF_4/32____LF_5/32_____RR_4/32_____LR_4/32_____ Tire Date codes – 2015 Visual Brake inspection – F__8MM________R___6MM______
AIR CONDITIONING SYSTEM – Complete Charge – [Includes: Air Conditioning system recover, evacuate and recharge.]
Russell H. gave our service a 5 star review on 8/29/2022

CRM Mitchell1

We Service and Repair all CRM Mitchell1 cars